Search By Part Number	Straight Accessories 90° Accessories 45° Accessories Miscellaneous Accessories Support Data/ Assembly Procedures   Descriptions SE1 SE2 SE3 SE4 SE5 SE6 SE7 SE8 SE9 SE10 SE11 SE12 SE14 SE16 SE17 SE18 SE19 SE20 SE22 SE25 SE26 SE27 SE28 SE29 SE30 CLICK HERE TO VIEW A LARGER IMAGE EXAMPLE BASIC PART NUMBER click here for SERIES CODE INFORMATION
SERIES CODE C MAX DIM A .875 B .875 C .781 D .500 E .750 F .438 FM .438 G .750 H 1.125 J .375 K .531 KA .281 KB .312 KC .250 KD .406 L .531 M .531 N .375 P 1.250 R .781 T .656 W .500 X .438 U .875      ENTRY SIZE D UNIFIED 2A THREAD E MAX DIM F MAX DIA G MAX DIM H MAX DIA CABLE ENTRY MAX MIN 04 .625 - 24 .843 .906 1.301 .957 .312 .188 06 .750 - 20 .906 1.093 1.301 1.145 .437 .281 08 .875 - 20 .969 1.187 1.301 1.270 .562 .344 10 1.000 - 20 .969 1.281 1.301 1.332 .625 .375 12 1.188 - 18 .969 1.500 1.332 1.556 .750 .500 16 1.438 - 18 1.062 1.719 1.426 1.775 .937 .625 20 1.750 - 18 1.125 2.062 1.613 2.115 1.250 .937 24 2.000 - 18 1.187 2.312 1.645 2.372 1.375 1.000 28 2.250 - 16 1.719 2.719 1.920 2.780 1.625 1.250 32 2.500 - 16 1.781 2.969 1.920 3.020 1.875 1.500 NOTES: Identified Per MIL-STD-130 Plating Index for Finishes Available Length to be specified by customer .5 inch increments (2.0 minium length, 2.5 inch minimum length for series codes B, H & P only. consult factory for availability of shorter lengths). Material; Adapter Components; Aluminum Alloy Per QQ-A-225 or QQ-A-591. Elastomers, Standard Neoprene Per MIL-R-3065 or Silicone (See Note 5) Per ZZ-R-765. Insert the following letter(s) for the function required: 'R' - Sleeve with RFI Rings. 'E' - Environmental (Neoprene Elastomers, Non-RFI). 'S' - Environmental (Silicone Elastomers, Non-RFI). 'RE' - RFI & Environmental (Neoprene Elastomers) 'RS' - RFI & Environmental (Silicone Elastomers) Insert the letter 'R' after series code designator to obtain spin coupling. Available on Series Codes C,F,FM,G & U only. (limited seal on F) Insert letter 'A' for MS3057-**A Clamp. 'F' for MS3057-**D Clamp. 'C' for 'C' nut. (no strain relief.) Insert letter: 'C' for chain attachment. (omit if not required) When entry size exceeds connector barrel ID two piece sleeve will be supplied. DIMENSIONS ARE IN INCHES Tolerance, unless otherwise specified: .X ± .03 (1.5) .XX ± .010 (0.8) .XXX ± .005 (0.4) Angles: ± 5 degrees Fractions ± 1/32 Click here for this part's assembly procedure (AP16)